4 Channel, 1000 W, Dedicated Installation Amplifier

Series: C Series

Model: C 10:4X

Part #: 992235005

Four channels in 2U
High continuous output power of 250 W per channel at 70 V, 4 ohms, 8 ohms, and 16 ohms
All channels individually selectable for lo-Z or hi-Z
Patented output stage based on Class D topology
High efficiency for lower thermal stress

More Product Information Below

Compare

Project List

Product Info

Tech Specs

Related Products

Documents

The C 10:4X is a versatile 4-channel amplifier, delivering 4 x 250 W* at 4 ohms, 8 ohms, 16 ohms or 70 Vrms (500 W at 100 Vrms is available by bridging two channels) from a 2U chassis.This amplifier is uniquely capable of adapting to a wide variety of demanding load conditions. Each channel has an individually configurable Voltage Peak Limiter (VPL), which allows the output to be optimized for any loudspeaker load – whether a single large subwoofer or a series of small 70 V loudspeakers (100 V in bridge mode). VPL works in combination with adjustable input gain (adjustable in 2-channel blocks) to achieve maximum headroom regardless of input levels or output impedances. Additionally a 35 Hz high pass filter may be inserted in each 2-channel section. Every C Series amplifier is ready for the NomadLink® network right out of the box. With NomadLink®, key amplifier parameters are displayed via DeviceControl PC software, and remote control of channel mutes and power on/off is under network control.

Four channels in 2U
High continuous output power of 250 W per channel at 70 V, 4 ohms, 8 ohms, and 16 ohms
All channels individually selectable for lo-Z or hi-Z
Patented output stage based on Class D topology
High efficiency for lower thermal stress
General Purpose Input/Output (GPIO)
NomadLink® network ready
Universal Power Factor Corrected PSU with IEC inlet
Efficient cooling
Comprehensive circuit protection and fault indication
Phoenix-style input connectors and barrier strip output connectors

Amplifier Signal Type - Audio
Amplifier Type - Other
Spec Sheet available - Yes

Maximum Frequency Response (Bandwidth): 20 kHz
Maximum Frequency Response (Bandwidth): 20000 Hz
Minimum Frequency Response (Bandwidth): 20 Hz
Minimum Frequency Response (Bandwidth): 0.02 kHz
Impedance: 20000 ohm
Number of Channels: 4
Number of Watts Per Channel: 250 Watt
Power Handling: 1000 Watt
Rack Units (Height): 2
Signal to Noise Ratio: 112 dB
Total Harmonic Distortion + Noise (THD+N): 0.10 %
AC Voltage: 265 Volts
Current Draw: 5 Amps
Depth: 13.50 in
Height: 3.46 in
Width: 19.02 in
Product Weight: 18.74 lbs
Color: Black/White
THD at 1 kHz and 1 dB below clipping: <0.05%
Channel separation (Crosstalk) at 1 kHz: >70 dB
Frequency response (1 W into 8 ohms) +0/-3 dB: 6.8 Hz - 34 kHz
Input Common Mode Rejection, CMR: 50 dB
Output impedance @ 100 Hz: 48 mOhm
VPL, selectable per ch. 3): 100, 63, 45, 32 V
VPL, when bridged 3) 1): 200, 126, 90, 64 V
Voltage Peak Limiter mode (per ch.): Hard / Soft
Amplifier gain selectable (all channels): 29, 32, 35, 38 dB
Default gain: 32 dB
Level adjustment (per ch.): Front-panel potentiometer, 21 position detented from -inf to 0 dB, hidden behind security panel/dust filter grille
Input connectors (per ch.): 3-pin Phoenix, electronically balanced
Output connectors (per ch.): Barrier strip 2-pole screw terminals
Output bridge mode: A+B and/or C+D, inputs A and C are input source
NomadLink® network: On board, 2 x RJ45 connectors
Intelligent fans (on/off): Yes, depending on presence of output signal
Power on/off and Remote enable on/off: Individual switches on front-panel
Cooling: Two fans, front-to-rear airflow, temperature controlled speed
General Purpose Outputs (GPO): Contact Closure types, 2-pole Phoenix
General Purpose Inputs (GPI): Contact Closure types, 2-pole Phoenix